Jump to content
Gimmie Shelter

Pegasus Hobbies T-Rex and Triceratops Dinosaurs

Recommended Posts

After a good 2 or so years of storage I felt it high time I got on and had a go at building these 2 lovely kits from Pegasus Hobbies; the Triceratops cow and Tyrannosaurus Rex posed stood over and pinning down a slain Triceratops calf. I have sold off my Pegasus Hobbies Spinosaurus to a club friend making these 2 kits the last of my Pegasus prehistoric collection.

The kits are complimentary to one another and are ideally suited to be built together or just as single display pieces. Cast in 100% solid vinyl plastic, both kits are very weighty and substantial. A lot of hot water treatment and dremeling was undertaken to get the various pieces fitted. Even after a lot of joint head shaving and heat treatments, the fits were so tight that virtually no glue was needed but I used long arm clamps overnight to keep constant pressure to the joint surfaces after a soak in freezing cold water upon assembly. Minimal filler was required at the time of assembly but I admit now to having to add a fair bit of Mr Surfacer 500 on top of the joint seam lines later on in the build after a base priming but not yet pictured here

You get a lot of dinosaur for your money from Pegasus and old Rexy is about 2 foot long when it's tail is inserted. I hope these kits give me as much pleasure as the Pegasus Hobbies Great White Shark did which I have just completed and is up on the forum elsewhere.

 

DSCF7715

 

DSCF7723

 

 

DSCF7716

 

 

DSCF7719

 

DSCF7720

 

DSCF7721

 

DSCF7722

 

The slain Triceratops calf with chest foot print from old Rexy

 

DSCF7717

 

DSCF7718

 

  • Like 1

Share this post


Link to post
Share on other sites

Another for me to watch as I have the Spinosaurus which can often be seen in the background of my in-progress photo's. Its been sat on my windowsill for about the same time yours has been waiting. Looking forward to learning from your painting methods.

Paul 

Share this post


Link to post
Share on other sites

A good number of hours have been spent going around in circles trying to get the seam lines filled so that they are not so visible - I have also managed to decide how to display the trio and have made a few modifications to the T-Rex and Triceratops calf which I will point out below. What a great pair of models these have turned out to be

 

TAIL ON

DSCF7736

 

THE 3 FIGURES

DSCF7743

 

TRICERATOPS COW

DSCF7745

 

HER BEAK

DSCF7747

 

DSCF7744

 

DSCF7746

 

COW ASSEMBLED

DSCF7751

 

THE DISPLAY

 

The Triceratops cow is posed with her head down and looks a bit dull considering her calf has just been struck down and is being stood on by old Rexy so I decided to use pose her climbing upfil to defend her calf while taking on old Rexy dino to dino style. Using foam, plaster and resin, I came up with the basic base from which I can add rocks and other bits of foliage onto to make this a true classic fight scene

 

DSCF7758

 

 

 

DSCF7754

 

DSCF7755

 

DSCF7757

 

DSCF7759

 

resin icing added to the cake base

 

DSCF7774

 

THE CALF

 

The calf is pictured to appear dead on the box art and certainly by the cast. I wanted to make mine look alive but pinned down - perhaps in the process of being rescued by the Cow so I cut the neck and bent it upwards so that the calf only looks to be pinned down but struggling to escape.

 

DSCF7768

 

DSCF7772

 

DSCF7773

 

The new neck pose

 

DSCF7771

 

REXY'S MOUTH

 

Rexy's tongue was not right for me either so I heated and twisted it so that it will look like it is flicking sideways out of the opened jaws.

 

DSCF7763

 

DSCF7762

 

 

Now ready for painting, and with their feet pinned for fixing on and off the diorama base, this is where the project stands today

 

DSCF7775

 

 

 

 

 

 

 

  • Like 1

Share this post


Link to post
Share on other sites
On ‎19‎/‎05‎/‎2018 at 13:54, Toolmaker said:

Another for me to watch as I have the Spinosaurus which can often be seen in the background of my in-progress photo's. Its been sat on my windowsill for about the same time yours has been waiting. Looking forward to learning from your painting methods.

Paul 

Hi - I have just found another Spino in my collection so if these 3 don't drive me insane I will give the Spino a go too afterwards

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


×